Cuddeback Expert Specifications download pdf (Page 8)

Longest Battery Life

Fastest Trigger Time

Page 15 of 37

use a small tweezers to access the jumper. If you lose the jumper your

Cuddeback will still function properly with the sensitivity set to standard. If you

are getting false detections lower the sensitivity using the jumper or software

menu.

The built in strobe flash has an effective range of about 30 feet. To assure night

images are properly exposed we recommend aiming Cuddeback at a tree 30 to

40 feet away. This will limit Cuddeback’s detection zone to the range of the

camera flash and camera lens. Best images will be taken when the animal is 10

to 15 feet from the Cuddeback.

INSTALLING CUDDEBACK IN THE FIELD

We recommend mounting Cuddeback to the largest tree in the area, about 10

feet from where you expect the animal to appear. Place Cuddeback about 3 to 4

feet off the ground, aiming slightly down. You can use Cuddeback’s Test

Mode to verify the detection distance.

We strongly recommend using the supplied Torx

screw to secure Cuddeback to

a tree. You will need a #25 Torx screwdriver. This assures solid mounting and

you will never have to worry about a bear, deer, or vandal knocking Cuddeback

off the tree. In addition, the supplied security cable can also be used. We also

recommend using a padlock to secure the battery cover – even if you are on

private property. This will assure that nobody tampers with your Cuddeback

Digital Camera.

WE STRONGLY RECOMMEND THAT YOU

ONLY USE THE TORX SCREW SUPPLIED.

Using a Torx screw eliminates the possibility of stripping the head. A Phillips

head or slotted head screw is very likely to strip and prevent you from removing

Cuddeback from the tree.

Note: if you do not use the security cable you should still attach the

supplied eye-bolt and wing nut to prevent insects from entering

Cuddeback.

Note: if you do not use the Torx screw, install the supplied Phillips-head

screw to prevent insects from entering Cuddeback.

FIELD CHECKING CUDDEBACK

Longest Battery Life

Fastest Trigger Time

Page 16 of 37

There are two methods you can use to field check your Cuddeback camera.

Using the a-switch method as described next, or you can follow this method.

1) To check Cuddeback remove the padlock (if installed), loosen the thumb

screw, and remove the battery cover.

2) Press (C KEY) to suspend Live Camera mode. The owner name (default

is Non Typical, Inc) will scroll across the LCD. You can skip this by

pressing the (C KEY). (This text can be changed, refer to the TheftStop

section in the Advanced Mode instructions).

3) If you programmed a lock password, you will be required to enter it to

access the menu systems. If you fail to enter the correct password,

Cuddeback will stop operating.

4) You should press the (M KEY) to determine if any images are saved.

5) If you have images taken, you can either 1) exchange the memory card to

view your images at home, or 2) attach a portable TV or camcorder to view

images.

6) We also recommend checking the battery level and free memory space (you

must be using Advanced Mode to do this).

7) You may want to archive the images to save time viewing images the next

time you check Cuddeback (in Advanced Mode only).

8) When you are finished you can 1) attach the battery cover and leave the

area; Cuddeback will automatically enter Live Camera mode within ten

minutes, or 2) activate Live Camera mode, replace the battery cover, and

leave the area.

9) If you want to move Cuddeback to a new location, we recommend

disarming Cuddeback to prevent erroneous images from being taken during

storage and movement.

THE A-SWITCH

Cuddeback’s a-switch (short for air-switch) allows you to determine how may

images Cuddeback has taken without opening the enclosure.

How to Activate the A-Switch

The ambient light level is the small center hole on the Cuddeback enclosure. It

is surrounded by a small ring that allows you to recognize it by feel. To use the

a-switch follow these steps:

1) Place your finger tightly over the a-switch opening for at least 9 seconds.

Observe the LED indicator as you do this.

2) The LED will illuminate for 1 second after the light is blocked for 9

seconds.

3) When the LED goes OFF immediately remove your finger. You must

remove your finger within ½ second of the light going off for the a-switch

to be recognized.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 18 19

Comments to this Manuals

No comments

Cuddeback Expert Specifications Page 8

Comments to this Manuals

Related products and manuals for Bridge cameras Cuddeback Expert